When the bag filter is running, the main ways of bag damage include combustion, wear, tearing of the bag bottom, and thread opening. The main reasons for bag combustion in bag filters are overheating of the flue gas (the flue gas temperature exceeds the working temperature of the bag) and spark burning of the bag.

一、避免煙氣過熱燒袋的主要措施有：

1、 The main measures to avoid flue gas overheating and bag burning include:

冷風閥安裝在鍋爐出口煙道上，或采取灑水減溫措施。鍋爐除塵器設計采用冷風閥。當煙氣溫度達到一定水平時，冷風閥打開，煙氣溫度可迅速降低；如果煙氣溫度持續升高到進氣閥打開溫度，每個房間的升降閥關閉進氣閥打開，煙氣直接通過旁通煙道排出。

The cold air valve is installed on the outlet flue of the boiler, or water spraying measures are taken to reduce temperature. The design of the boiler dust collector adopts a cold air valve. When the flue gas temperature reaches a certain level, the cold air valve opens, and the flue gas temperature can quickly decrease; If the flue gas temperature continues to rise to the opening temperature of the inlet valve, the lifting valve of each room closes and the inlet valve opens, and the flue gas is directly discharged through the bypass flue.

二、避免火星燒袋的措施有：

2、 Measures to avoid sparks burning bags include:

1)選用防火材料濾袋。

1) Select fireproof material filter bags.

2)選擇預除塵技術，袋式除塵器本身采用氣流分布隔板，避免火星與袋直接碰撞，使直徑較大的未燃顆粒直接落入人料倉庫。

2) Choosing pre dust removal technology, the bag filter itself adopts airflow distribution partition to avoid direct collision between sparks and the bag, causing larger diameter unburned particles to directly fall into the human material warehouse.

三、布袋磨損的主要原因有：

3、 The main reasons for bag wear are:

1)煙氣分布不均勻，氣室局部過濾風速過高，加重粉塵沖擊，磨損布袋；2）布袋間距離過小，或籠骨彎曲，籠骨與布袋底部間隙過小，3）噴嘴與布袋口垂直誤差直接沖刷布袋上部磨損；4）布袋清洗過頻繁或噴射壓力過高也會加速布袋的磨損。

1) Uneven distribution of flue gas, high local filtration wind speed in the air chamber, aggravating dust impact, and wearing the cloth bag; 2) The distance between the bags is too small, or the cage bones are bent, and the gap between the cage bones and the bottom of the bag is too small. 3) The vertical error between the nozzle and the bag mouth directly washes away the wear on the upper part of the bag; 4) Frequent cleaning of cloth bags or high spraying pressure can also accelerate the wear of cloth bags.

四、減少布袋磨損的措施有：

4、 Measures to reduce bag wear include:

1)合理分布袋，平衡氣流。

1) Reasonably distribute bags and balance airflow.

2)安裝時應控制噴嘴與布袋口的對正關系。

2) During installation, the alignment between the nozzle and the bag opening should be controlled.

3)運行初期應保持較低的噴射壓力和較長的噴射周期，并在布袋表面保持一定厚度的初始粉塵層。

3) At the initial stage of operation, a lower injection pressure and longer injection cycle should be maintained, and a certain thickness of initial dust layer should be maintained on the surface of the cloth bag.

本文由多工位焊煙除塵設備整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://www.68428.com.cn我們會有更多精彩內容等你查看。

This article is organized and published by multi-station welding fume dust removal equipment. Have you gained some understanding of these contents? For more information, please click on: http://www.68428.com.cn We will have more exciting content waiting for you to check out.